Room Thermostat help

It is best to install the Room thermostat in a place in the room where you are usually located, i.e. near the sofa in the living room at a height of approx. 1.50m. If possible, do not install the device on an outside wall, near a window, near a heat source or in a place exposed to direct or indirect sunlight.

The Room thermostat can be installed in just a few simple steps. All you need is the Bosch Smart Home app and the accessories included in the packaging. After starting the Bosch Smart Home app, you will be guided through the individual installation steps.

It can happen with both the Room thermostat and the Radiator thermostat that the display remains dark when the batteries are changed. It appears as if the batteries are flat.

In this case, please remove the batteries and press the buttons on the devices several times. After reinserting the batteries, the devices should now be accessible again without any problems.

In Germany, flush-mounted boxes normally have a depth of 50 mm. This is sufficient for our thermostats.
In older households, the flush-mounted boxes are sometimes only 40 mm deep. For this application, there are so-called flat boxes, which have a depth of only 35 mm.

Please note that some of the products described and their functions may only be available in Germany and Austria.

The typical service life of the batteries is at least 1 year with typical use. If the battery capacity falls below a critical level, the Bosch Smart Home app informs you in good time.

The battery symbol also lights up on the device display and starts to flash.

You can connect up to 6 devices directly to a Room thermostat. If you have assigned several devices to a Room thermostat, you will find the corresponding overview on the device configuration page of the Room thermostat.

The surplus Radiator thermostats are controlled as if there were no Room thermostat in the corresponding room. Each Radiator thermostat regulates according to its own temperature measurement. The setpoint temperature is then sent to all devices by the Smart Home controller.

To restore the factory settings, please proceed as follows:

1. please remove at least one battery first. Please wait 20 seconds or briefly press the control dial of your device again after removing the battery. This will ensure that the factory settings can be restored successfully.

2. then reinsert the battery and hold down the adjusting wheel while inserting it.

3. wait until "rES" appears on the display.

4. briefly release the adjusting wheel, then immediately press the adjusting wheel again and keep it pressed until the LED lights up green.

5. release the adjusting wheel and the appliance will restart. The process is complete when the display shows the measured temperature and humidity again.

The temperature sensors of the Smart Home Motion detector, the Twist or the Twinguard are not suitable for room temperature control, as they only take temperature measurements at irregular intervals. Only our Room and Radiator thermostats are suitable for room temperature control.

The humidity is shown on the display of the device and in the app under the room overview.

Replacing your first generation Bosch Smart Home Room thermostat (battery)

If your first-generation Bosch Smart Home Room thermostat (battery) is defective, you will receive a replacement device under the guarantee or warranty.

Replacement device:

You will receive a Bosch Smart Home Room thermostat II (battery) (model number: 8-750-002-414).

We hope that this solves your problem and that you continue to enjoy your smart home system.

The Room thermostat is an ideal addition to Radiator thermostats or Smart plugs in the air conditioning sector. Unlike the underfloor heating Room thermostat, it can be mounted anywhere in the room using screws or adhesive and can be freely adjusted as a temperature sensor.

Further information can be found on the corresponding product page of our webshop. Please follow thisLink.

The Smart Home Room thermostat enables even better heat regulation throughout the room and is therefore the perfect addition to your Radiator thermostats. Control up to six radiators per room simultaneously and centrally with your Room thermostat. Instead of directly on the radiator, the smart room thermostat measures the temperature where you place it. This means that your individual desired temperature is reached exactly where it is most important to you. Especially in large rooms or with concealed radiators, temperature control is much more efficient with the smart Room thermostat. You save energy and gain comfort.

The Room thermostat does not measure the temperature locally on the radiator, but centrally where you install it in the room. The desired temperature and the temperature measured at the installation location are transmitted to the individual Radiator thermostats. These only heat as much as necessary to keep your desired temperature constant in the room. This allows you to enjoy greater heating comfort throughout the room.

Further information can be found on the corresponding product page of our webshop. Please follow thisLink.

The exact scope of delivery of the Bosch Smart Home Room thermostat can be found on the corresponding product page of our webshop. Please follow thisLink.

Communication between the Room thermostat and the Bosch Smart Home controller takes place via a proprietary radio protocol (868MHz).