Light/shutter control II help

We will shortly be providing an accessory that will enable you to install the Light/shutter control II in the existing flush-mounted box to save space.

The accessories can also be combined with rockers and frames from a large number of switch series from well-known brand manufacturers.

Yes, the built-in Light/shutter control II can also be switched back to teach-in mode at a later time. To do this, press the system button on the Light/shutter control II again. If a push-button/switch is already fitted, you can also activate the mode conveniently by pressing any button.

Before purchasing, please make sure that the installation location of the Bosch Smart Home Light/shutter control II offers sufficient space.
You need a 230 V AC power supply for installation. A phase and a neutral conductor must be available. Furthermore, please ensure that you have a box depth of at least 50 mm, ideally 60 mm.

For more information, please consult theOperating instructionsof the Bosch Smart Home Light/shutter control II.

Please also refer to our installation video in this article. If there are any problems displaying the video, you can also find our installation and reset videos on our Bosch Smart Home YouTube channel at the following linkLink.

As long as the Bosch Smart Home Light/shutter control II has not been configured as Light control or Shutter control in the Bosch Smart Home app, the inputs S1/S2 do not execute any switching commands.

Yes, you have the option of changing the button assignment of your Bosch Smart Home Light/shutter control II during the installation process. After installation, you also have the option of changing the button assignment in the device management of the device.

The flush-mounted box behind the switch should have a depth of at least 50mm. However, we recommend using a box with a depth of at least 60mm.

Yes, you can change the switch type in the device management in your Bosch Smart Home app.

If the end position of your roller shutter is not detected correctly, open the Bosch Smart Home app. Navigate to the relevant device in the device settings of the Bosch Smart Home app and deactivate the automatic end position detection. Now carry out the calibration manually.

The economy changeover switch is a special type of changeover switch. In contrast to normal changeover switching, the Bosch Smart Home Light/shutter control II does not have to be installed behind the switch but directly in front of the consumer. The economy changeover circuit only has one switched phase. Have your electrician check whether an extra cable can be pulled.

If the childproof lock was activated during the initial setup of the Bosch Smart Home Light/shutter control II, the Light/shutter control II cannot be operated using the switch/button.

You can make adjustments to the device settings via the device management. Deactivate the parental control here.

The device is defective. Please send your proof of purchase to theServiceat service@bosch-smarthome.com

The teach-in mode or another process was successful.

A maximum of 400 watts may be applied.

You can control as many lights as you like until the maximum switching capacity of 500W ohmic power is reached. With the Bosch Smart Home Light/shutter control II, you also have the option of controlling two lights (i.e. two channels) to which several consumers are connected.

The teach-in mode was not successful or the process has failed.

To extend the range of the Bosch Smart Home Light/shutter control II, either bring the Bosch Smart Home Light/shutter control II closer to the Bosch Smart Home controller or place a Bosch Smart Home plug compact halfway. This serves as a range extender.

Depending on whether the tilt angle of your slats is 90° or 180°, you have the option of tilting the slats accordingly with manual control via the Bosch Smart Home app.

To reset the Bosch Smart Home Light/shutter control II to the factory settings, proceed as follows:
1) Press and hold the system button for approx. 4 seconds until the status LED flashes orange quickly.
2) Briefly release the system button and press again until the LED briefly lights up green.
3) The device will now restart. In the Bosch Smart Home app under "More" >> "Devices", you may need to delete the Bosch Smart Home Light/shutter control II from the app.

Alternatively, the following procedure is also possible:

When installed with the switch connected:

Press the switch 12 times in a maximum period of 10 seconds.

The device then restarts.

To register the device again, you must first delete it in the Bosch Smart Home app.

In installed state with connected push-button:

Press the button 6 times within a maximum period of 10 seconds.

The device then restarts.

To register the device again, you must first delete it in the Bosch Smart Home app

Check whether your Bosch Smart Home Light/shutter control II can still be controlled manually. If this is the case, remove the power cable from your controller and restart it. Please also check whether the range of your Smart Home controller is sufficient. If you have connection problems, you can use a Bosch Smart Home plug compact to extend the range. If the problem persists, reset the flush-mounted switch to the factory settings and integrate it again.
If this does not lead to a solution, please contact either the Bosch Smart HomeCommunityor ourService team.

The teach-in mode of your Bosch Smart Home Light/shutter control II is active or the device is communicating with the Bosch Smart Home controller.

A maximum inductive load of 2 x 200 watts may be applied.

If the Bosch Smart Home Smoke alarms or Twinguards detect a fire, the Bosch Smart Home Light/shutter control II behaves as follows:

If you use the Bosch Smart Home Light/shutter control II as a light control, it will switch on the corresponding lamps and illuminate an escape route for you.

If you use the Bosch Smart Home Light/shutter control II as a shutter control, it will open the corresponding shutters and thus provide you with an escape route.

Yes, you can also control slats with the Bosch Smart Home Light/shutter control II.

A maximum ohmic load of 2 x 500 watts may be applied.

Yes, you can activate the parental control in the device management in the Bosch Smart Home app. The Bosch Smart Home Light/shutter control II can then only be operated via the Bosch Smart Home app. There is the exception that the roller shutters are raised automatically in the event of a fire for safety reasons.

The Bosch Smart Home Light/shutter control II may only be used outdoors with a protective housing (IP66).

The Bosch Smart Home Light/shutter control II has a size of 40.5 x 47 x 22mm. Please check whether you have enough space at the installation location before purchasing and before installation. We recommend an installation box depth of at least 60mm or more. Please leave the installation to a specialist.

The Bosch Smart Home Light/shutter control II uses the ZigBee 3.0 radio protocol and therefore also serves as a range extender for other Bosch Smart Home devices that use ZigBee 3.0.

No. In the Bosch Smart Home app, the energy consumption is displayed collectively.

Yes, the Bosch Smart Home Light/shutter control II can control roller shutters, blinds and awnings.

If you use the Bosch Smart Home Light/shutter control II as a light control, you have the option of viewing the current and cumulative power consumption in the Bosch Smart Home app. The current power is shown in watts and the cumulative consumption in watt-hours.

The Bosch Smart Home Light/shutter control II is a product for controlling shutters, awnings and blinds. Alternatively, one or two lights or other loads can be switched independently of each other. The Bosch Smart Home Light/shutter control II measures the power consumption of connected lights and loads.

No. No adapters are required for the Bosch Smart Home Light/shutter control II.

Yes, the Bosch Smart Home Light/shutter control II can be operated with switches without any problems. During installation, you can choose between control with switches and push-buttons.

No. Unlike the first generation Light/shutter control, the Bosch Smart Home Light/shutter control II does not require a switch to be replaced, as the Bosch Smart Home Light/shutter control II is placed between the existing switch and circuit.

Yes, the Bosch Smart Home Light/shutter control II also works with a impulse relay.

Yes, if you use the Bosch Smart Home Light/shutter control II as a light control, this is part of the presence simulation. If you use the Bosch Smart Home Light/shutter control II as a shutter, you can use automation to store individual times for opening and closing.

Yes, if you use the Bosch Smart Home Light/shutter control II as a Light control. As with the Bosch Smart Home Radiator thermostats, Room thermostats, Smart plugs and Light controls, you have the option of setting a time control. If you use the Bosch Smart Home Light/shutter control II as a shutter control, you can use automations in the Bosch Smart Home app to store an individual time control.

You can integrate the Bosch Smart Home Light/shutter control II into Amazon Alexa, Google Assistant and Apple HomeKit.

The Bosch Smart Home controller including the Bosch Smart Home app (iOS, Android) is required for the partner connection.